Home / Products / Conductor Accessories / Network Underground / MICON Limiter Assemblies

MICON Limiter Assemblies

A tee connector composed of a clamp type run element and a compression type connector for the tap.
For rubber or paper insulated cable, a limiter tap for making tap connections from a continuous or cable ring bus in a transformer vault or manhole junction.
A 10 outlet fusible crab connector designed to connect cables to a common point.
A 6 outlet fusible crab connector for use with 500 MCM cables. Each outlet is provided with an independent fusible link which is connected to a common junction within the connector.
A fully submersible secondary connector for making a number of service connections to a single secondary lead. The connector leads are all protected with high density cross linked polyethylene insulation.
An insulating cap to protect unused outlets on types CB10R and CB6R fusible crab connectors.
A tee coupler for joining two cables on the run and taking off a right angle tap at the junction. Made of high conductivity copper and completely tin plated.
A thermal insulating wedge which is placed over the compressed tubular sections of outlets on types CB10R and CB6R fusible crab connectors.
A seamless sleeve coupler for splicing two cables end to end. This coupler is designed to fit the assembling dies of all standard hydraulic presses.
A precision made compression terminal lug for a full range of conductor sizes with 1, 2, and 4 hole pads in the larger sizes.
A seamless sleeve reducing coupler for splicing two cables end to end.
A split sleeve coupler for soldering two cables end to end.
A split tinned copper connector for soldering two or four equal size cables.
A split tinned copper reducing coupler for soldering a wide range of conductor sizes.
A tinned copper connector for splicing and tapping a continuous run available for a wide range of cable sizes.
A pure copper fusible link with a predetermined time-current characteristic cemented into a shell to make a complete arc proof limiter assembly.
A limiter stud connecting terminal for joining four 500 MCM cables to network protector. These terminals are furnished to the network protector.
A cast bronze tee connector whose tap element provides a watertight weather seal on the tap cable when the body and shroud is taped to the insulation of the cable.
For use with MICON Limiter Assembly Types ML-R123, ML-P123, and ML-PL123, a two piece MYPAR sleeve for insulating the MICON limiter and shell assembly.
The MICON long limiter assembly is designed to establish a fusible connecting point at a MICON outlet for oil-filled paper insulated cable.
For use with MICON Long Limiter Assembly Type ML-PL123, the MICON long limiter, for oil filled paper insulated cable, is designed to provide a fusible connecting point to the MICON outlet.
The MICON limiter assembly is designed to establish a fusible connecting point at a MICON outlet.
For Use with MICON Limiter Assembly Types ML-R123, ML-P123, and ML-PL123, a composition molded shell consisting of two symmetrical halves with interlocking fingers.
For use with MICON limiter assembly types ML-R123 and ML-P123, the MICON limiter is designed to provide a fusible connecting point to the MICON outlet. The fusible section is made to close tolerances to insure consistent conformity with the fusing time-current curves.
Provides a fusible tap connection to a continuous or ring bus.
An offset tap connector for making a tap connection from a ring bus.
A compression terminal designed to fit terminal ends of type RLM-B limiter mounting block.
A renewable MICON Limiter connector for making a fusible connection to an outlet of a MICON.
The renewable MICON limiter link assembly is designed to establish a fusible connection to a MICON unit. The renewable link offers a quick and inexpensive means of re-energizing a cleared circuit.
Link connector for making fusible connections to a flat bar bus or contact pad.
A renewable type limiter link coupler for connecting rubber or paper insulated cables on end and providing a fusible element for cable protection.
A MYPAR rubber compound insulating sleeve for providing an insulating cover over the Renewable Limiter Link, type RLM-E and Renewable Micon Limiter Link, type RLB-E.
For use with renewable limiter link assembly types RLB-E and RLM-E, an insulating bushing designed to effect a close fit over cable insulation.
An insulating adapter that creates a close fit between MICON outlet and RLM-1 Limiter sleeve.
For use with renewable limiter link assembly types RLM-E and RLB-E, a high impact, heat resistant, fiber reinforced phenolic resin base insulating mounting block.
An insulating renewable limiter link assembly which serves as both a fuse and coupler. The renewable link offers a quick and inexpensive means of re-energizing cleared circuits.
A cast bronze terminal with a cast hood serving as a shroud over the insulation of the cable.